How to Install Snort on Ubuntu 20.04

Last updated: July 19, 2022 | Bobbin Zachariah

Snort is an open-source lightweight network Intrusion Prevention System for running a network intrusion detection system (NIDS). Snort is used to monitor the package data sent/received through a specific network interface. Network intrusion detection systems can catch threats targeting your system weakness and vulnerabilities using signature-based detection and protocol analysis technologies.

When NIDS software is installed and configured correctly, can identify different kinds of attack and suspicions things like CGI attacks, network policy violations, SMB probes, malware infections, a compromised system, stealth port scan, etc.

In this tutorial, we learn how to install Snort 3 on Ubuntu 20.04.

Some of the new Snort 3 features:

  • Support multiple packet processing threads
  • Allows multiple packet processing
  • Autogenerate reference documentation
  • Use a simple scriptable configuration
  • Make key components pluggable
  • Allows users to write their own plugins
  • Shared configuration and attribute table
  • Allows rules to run quicker

Step 1: Update the system

First, update and upgrade your Ubuntu system

sudo apt update
sudo apt upgrade

Step 2: Install Required Dependencies

Ubuntu default repository has snort package. The snort package available there is the old version. To install Snort 3, we have to build from the source. Before installing Snort 3, we need to install the prerequisite and required libraries.

Install Snort 3 dependencies packages with the following command:

sudo apt install build-essential libpcap-dev libpcre3-dev libnet1-dev zlib1g-dev luajit hwloc libdnet-dev libdumbnet-dev bison flex liblzma-dev openssl libssl-dev pkg-config libhwloc-dev cmake cpputest libsqlite3-dev uuid-dev libcmocka-dev libnetfilter-queue-dev libmnl-dev autotools-dev libluajit-5.1-dev libunwind-dev

After dependencies are installed, created a directory where you compile and kept source files for Snort with the following command:

mkdir snort-source-files
cd snort-source-files

Then, download and install the latest version of the Snort Data Acquisition library (LibDAQ). For installing LibDAQ we'll need to build and install it from the source with the following command.

git clone
cd libdaq
make install

The next dependency is Tcmalloc, which will optimize memory allocation and provide better memory usage.

Install Tcmalloc with the following command.

cd ../
tar xzf gperftools-2.9.tar.gz 
cd gperftools-2.9/
make install

Step 3: Install Snort 3 on Ubuntu 20.04

After dependencies are set up, we are going to download and install Snort 3 on Ubuntu 20.04.

01. Clone Snort 3 official GitHub repository.

cd ../
git clone git://

02. Change the directory to Snort3

cd snort3/

03. From there configure and enable tcmalloc with the following command.

./ --prefix=/usr/local --enable-tcmalloc

04. Navigate to build directory and compile and install Snort 3 using make and make install with the following command.

cd build
make install

05. When the installation is done, update shared libraries.

sudo ldconfig

Snort by default is installed to /usr/local/bin/snort directory, it is good practice to create a symbolic link for /usr/sbin/snort

sudo ln -s /usr/local/bin/snort /usr/sbin/snort

06. Verify Snort 3 installation

snort -V


,,_     -> Snort++ <-
   o"  )~   Version
    ''''    By Martin Roesch & The Snort Team
            Copyright (C) 2014-2021 Cisco and/or its affiliates. All rights reserved.
            Copyright (C) 1998-2013 Sourcefire, Inc., et al.
            Using DAQ version 3.0.4
            Using LuaJIT version 2.1.0-beta3
            Using OpenSSL 1.1.1f  31 Mar 2020
            Using libpcap version 1.9.1 (with TPACKET_V3)
            Using PCRE version 8.39 2016-06-14
            Using ZLIB version 1.2.11
            Using LZMA version 5.2.4

If you see a similar output, then Snort 3 is installed successfully.

Configure Network Interface Cards

Find the interface on which Snort is listening for network traffic and enable promiscuous mode to be able to see all the network traffic sent to it.

ip link set dev eh0 promisc on

Verify with the following command.

ip add sh eth0


2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER UP> mtu 1500 qdisc mq state UP group default qlen 1000
     link/ether f2:3c:92:ed:7e:d8 brd ff:ff:ff:ff:ff:ff
     inet brd scope global dynamic eth0
        valid_lft 72073sec preferred_lft 72073sec
     inet6 2600:3c02::f03c:92ff:feed:7ed8/64 scope global dynamic mngtmpaddr noprefixroute 
        valid_lft 60sec preferred_lft 20sec
     inet6 fe80::f03c:92ff:feed:7ed8/64 scope link 
        valid_lft forever preferred_lft forever

Next, disable interface Offloading to prevent Snort 3 from truncating large packets, max to 1518 bytes. Check if this feature is enabled with the following command.

ethtool -k eth0 | grep receive-offload

If seeing this output that GRO is enabled while LRO is fixed or LRO is enabled.


generic-receive-offload: on
large-receive-offload: on

Disable it with the following command.

ethtool -K eth0 gro off lro off

Two ensure the changes persists across system reboot, we'll need to create and enable a systemd service unit to implement the changes.

sudo nano /etc/systemd/system/snort3-nic.service

Paste the following configuration that points to your network interface.

Description=Set Snort 3 NIC in promiscuous mode and Disable GRO, LRO on boot

ExecStart=/usr/sbin/ip link set dev eth0 promisc on
ExecStart=/usr/sbin/ethtool -K eth0 gro off lro off 


Reload systemd configuration settings:

sudo systemctl daemon-reload

Start and enable the service on boot with the following command:

sudo systemctl enable --now snort3-nic.service


Created symlink /etc/systemd/system/ → /etc/systemd/system/snort3-nic.service.

Verify the snort3-nic.service with:

sudo systemctl status snort3-nic.service


● snort3-nic.service - Set Snort 3 NIC in promiscuous mode and Disable GRO, LRO on boot
      Loaded: loaded (/etc/systemd/system/snort3-nic.service; enabled; vendor preset: enabled)
      Active: active (exited) since Sat 2021-09-18 12:35:17 UTC; 4min 59s ago
     Process: 182782 ExecStart=/usr/sbin/ip link set dev eth0 promisc on (code=exited, status=0>
     Process: 182783 ExecStart=/usr/sbin/ethtool -K eth0 gro off lro off (code=exited, status=0>
    Main PID: 182783 (code=exited, status=0/SUCCESS)
 Sep 18 12:35:17 li72-186 systemd[1]: Starting Set Snort 3 NIC in promiscuous mode and Disable >
 Sep 18 12:35:17 li72-186 systemd[1]: Finished Set Snort 3 NIC in promiscuous mode and Disable >

Install Snort 3 Community Rulesets

In Snort, rulesets are the main advantage for intrusion detection engine. There are three types of Snort Rules: Community Rules, Registered Rules, Subscriber Rules. Community rules are submitted by the open-source community or snort integrators.

We're going to show how to install the Community Rules.

First, create a directory for the Rules in the /usr/local/etc/snort

mkdir /usr/local/etc/rules

Download Snort 3 community rules. You can find it on the official Snort3 download page.


Extract downloaded rules and put them in the directory that we previously create /usr/local/etc/rules/

tar xzf snort3-community-rules.tar.gz -C /usr/local/etc/rules/

Snort 3 includes two main configurations files, snort_defaults.lua and snort.lua.

The snort.lua file contains Snort's main configuration, allowing the implementation and configuration of Snort preprocessors, rules files inclusion, logging, event filters, output, etc.

The snort_defaults.lua files contain default values such as paths to rules, AppID, intelligence lists, and network variables.

When rules files are extracted and placed, we're going to configure one of these config files called snort.lua. Open the file with your favorite editor and will see something similar config.

... -- HOME_NET and EXTERNAL_NET must be set now -- setup the network addresses you are protecting
HOME_NET = 'server_public_IP/32'

-- set up the external network addresses.
-- (leave as "any" in most situations)

Set the network which you want to protect against attacks as the value for the HOME_NET variable, and point EXTERNAL_NET variable to HOME_NET variable.

Save and exit.

You can also edit Snort defaults in the /usr/local/etc/snort/snort_defaults.lua and under IPS section you can define the location to your rules.

ips = 
-- use this to enable decoder and inspector alerts     
--enable_builtin_rules = true,     

-- use include for rules files; be sure to set your path     
-- note that rules files can include other rules files     
include = '/usr/local/etc/rules/snort3-community-rules/snort3-community.rules' 

Save and exit.

Running Snort as a Service

If you are going to run Snort as a service daemon in the background, it is also possible to create a systemd service unit for Snort. It is prudent to run it as a non-privileged system user

Create a non-login system user account.

sudo useradd -r -s /usr/sbin/nologin -M -c SNORT_IDS snort

Then, create a systemd service unit for Snort to be run as a snort user. Adjust and match to your network interface.

sudo nano /etc/systemd/system/snort3.service

Paste the following configuration.

Description=Snort 3 NIDS Daemon

ExecStart=/usr/local/bin/snort -c /usr/local/etc/snort/snort.lua -s 65535 -k none -l /var/log/snort -D -i eht0 -m 0x1b -u snort -g snort


Reload the systemd configuration.

sudo systemctl daemon-reload

Set the ownership and permissions on the log file.

sudo chmod -R 5775 /var/log/snort
sudo chown -R snort:snort /var/log/snort

Start and enable Snort to run on the system boot:

sudo systemctl enable --now snort3

Check the service status to confirm if it is running.

sudo systemctl status snort3


● snort3.service - Snort 3 NIDS Daemon
      Loaded: loaded (/etc/systemd/system/snort3.service; enabled; vendor preset: enabled)
      Active: active (running) since Sat 2021-09-18 12:44:32 UTC; 6s ago
    Main PID: 182886 (snort)
       Tasks: 2 (limit: 1071)
      Memory: 62.6M
      CGroup: /system.slice/snort3.service
              └─182886 /usr/local/bin/snort -c /usr/local/etc/snort/snort.lua -s 65535 -k none >
 Sep 18 12:44:32 li72-186 systemd[1]: Started Snort 3 NIDS Daemon.


In this tutorial, we learned how to install the Snort 3 network intrusion detection system on Ubuntu 20.04.

Linux is not 100% immune to Viruses and suspicious things, it is always better to have some tool installed and to be sure that no one is trying something suspicious across your device and network. Other alternatives for Snort that you can investigate: Ossec, Palo Alto Networks Next-Generation Firewall, Next-Generation Intrusion Prevention System (NGIPS).

Thanks for reading, please provide your feedback and suggestions in the comment section.



Please add comments below to provide the author your ideas, appreciation and feedback.

Leave a Reply

Leave a Comment